Radionics Machine Q&A Working With Manifestor

Radionic Machine Software

Radionics Machine Working With Radionic Manifestor 

Users Questions & Answers

 

Q: Hello MY friend CAN you just help me with this?
Can you explain to me this with a photo example
One physical copy of the structural link image
One digital copy of the structural link image (image file on your computer)

WHEN WE ARE  DO WE MOVE THE TREND DIALS OR WITNESS DIALS?
FREQUENCY DIAL do we move?

 

A: WHEN WE ARE WORKING WITH RADIONIC MANIFESTOR, just use the S-Link image as in the image below. Turn on your Genie 2000 and put your paper S-Link image in front of the machine. Then load your scanned S-Link copy into radionic manifestor with the S-link Button and set your rates in radionic manifestor (as described in the radionic manifestor help pdf)
The Chi will be sent from the image in front of your machine to the copy image in the software (a structural link )

 

Radionics Machine Software
Linking the radionics machine to software with structural links

 

Q: when we connect genie 2000 with radionic manifestor pro 3 . Do we need to move the trend and witness dials and frequency in genie 2000?
To link radionic manifestor and genie 2000 how long do we need to keep the physical copy in front of the output pipe?

When we have connected the genie with manifestor 3 we need to put anything in trend and witness plate in genie?

Q: when we connect genie 2000 with radionic manifestor pro 3 . Do we need to move the trend and witness dials and frequency in genie 2000?

A: You can set the frequency dial, but set the trend and witness dials to zero (0).

Q: To link radionic manifestor and genie 2000 how long do we need to keep the physical copy in front of the output pipe?

A: For as long as you are running the software.

Q: When we have connected the genie with manifestor 3 we need to put anything in trend and witness plate in genie?

A: No

 

Setting The Trend Rate:

Place your image/text on the left Trend plate, now whilst rubbing the stick pad slowly turn the first dial until enough resistance is felt on the stick pad that it stops your fingers from sliding. At the exact point you fingers stop sliding on the stick pad stop turning the dial, the rate for that dial is now set.

Repeat the above steps for all 6 dials.

If you think you may need to use the rate again write down each number for its corresponding dial.

Setting A Balance Rate:

A balance rate is a way of reversing or correcting an outcome or condition, or balancing seeds and plants to increase there vitality.

This can be done by setting your rates as above then taking the original dial rate from 10, then reset your dial to the balance number, repeat for all 6 dials.

Copyright© Kieron Waterman. All rights reserved.

10 – 7 = 3 10 Minus 7 Equals 3

7 being the dial rate. This is the number you entered from a rate book or stick the stick pad. 3 is the new balance rate. This is the new setting for that dial, which is the result from the above simple calculation. When completed for all the dials used this corrects or balances the illness or condition. This will work with either 0-10 or 0-100.

Entering Radionics Machine Base 10 Rates from A Rate Book:

When entering rates directly from a rate book, dial each number into the corresponding dial (from left to right) then place your Witness image on the Witness plate and turn the machine on. Please note, there is no need to use the stick pad or the trend plate when using rates from a rate book or your own previously noted rates.

When working from Base 10 rate books view the dial graduations as 0 to 10.

Each dial represented one digit in the rate, so to set the rate for Fuji Cherry 2595952

You would set the dials as below:

Dial 1 to 2 Dial 2 to 5 Dial 3 to 9 Dial 4 to 5 Dial 5 to 9 Dial 6 to 5

Any numbers in the rate that are leftover are to be ignored, as in this case the number 2.

Creating Base 10 Rates Rates:

You will need to round the number up or down, (whichever number the dial mark is closest too) and view it as 0-10 as in Base 10 rate books.

 

radionics manifestor pro 3 radionics software

Copyright© Radionics Machine. All rights reserved

Leave a Reply